日本xxxx,国产美女被遭强高潮免费网站,欧洲多毛BBBBXXXX,金瓶梅1-5电影观看在线

本站熱搜:氧化鋯氧量分析儀,盤裝式氧量分析儀,電磁流量計,WSS雙金屬溫度計
  • 技術文章ARTICLE

    您當前的位置:首頁 > 技術文章 > Common faults and causes of zirconia oxygen analyzers

    Common faults and causes of zirconia oxygen analyzers

    發布時間: 2024-12-13  點擊次數: 436次

    1. System maintenance.

    If the oxygen indicator shows zero or no oxygen indication in the oxygen quantity converter, first check whether the oxygen indication circuit open. If the circuit is normal, check whether the zirconia probe is normal. At a temperature of 700℃, measure the DC millolt value of the oxygen cell. If the potential is greater than 1 millivolt and the resistance is greater than 100Ω, it indicates the probe is aged and needs to be replaced with a sensor or probe. If the potential is less than 1 millivolt and the resistance is less than100Ω, it indicates an open circuit in the wiring, which should be checked and handled one by one.

    2. constant temperature system failure.

    (1) If the heating temperature cannot be maintained, check whether there is a short circuit or open circuit in the resistance wire inside the heating furnace The normal resistance of the heating furnace wire is about 60-80Ω. If the resistance wire is open or the resistance measured by the multimeter less than 60Ω, the heating furnace wire should be replaced.

    (2) When the converter shows that the temperature is too high or out of control, it not only causes inaccurate oxygen display but also acceler the aging or damage of the zirconia head. At this point, you should immediately check if the thermocouple is open-circuited, or a multimeter to check the thermocouple. If the resistance is greater than 20Ω, it is judged that the thermocouple is open-cuited, and the thermocouple and zirconia head should be replaced; another reason for the temperature失控is: relay or temperature control circuit failure, relay or temperature control circuit failure will cause the oxygen converter to always be in one of the heating voltages of the heating furnace, thus leading to an increase in.

    3. oxygen cell fault.

    (1) After the oxygen cell has been used for a period of time, the contact points of its leads may become oxidized, resulting in contact or detachment. This can cause the Em value (in units of a multimeter) to fluctuate and become unstable. Observe the oxygen cell and take action.

    (2) When the oxygen signal deviation is too large or inaccurate, it may be due to a short circuit in the zirconia electrode, which case the wiring of the zirconia cell should be checked for short circuits. When the temperature does not rise, if the internal resistance is less than 0Ω, it indicates a short circuit in the electrode, and the zirconia head needs to be replaced.

    (3) During the operation of the oxygen measurement device, if the background potential exceeds 10mV or is less than -30mV, it must be recalibrated. If the background potential remains abnormal after calibration, it indicates that the probe has aged and can no longer be used.

    4. pneumatic circuit failure.

    (1) The zirconia head is clogged with ash, causing an obstruction in the reference gas circulation. This results in a decrease in probe output potential Em and an increase in the background potential Eo. In this case, blowing several times with a bulb syringe at the gas inlet of the will resolve the issue after the gas line is unclogged.

    (2) Oxygen cell ash blockage: The probe should be removed from the ash blockage and the filter should be reinstalled.

    (3) Probe leakage has a significant impact on the probe.

    5. The oxygen content on both sides of the boiler is too high.

    By adjusting the boiler combustion conditions, when starting or stopping the boiler fan or coal mill group, if the oxygen content deviation on both sides of the boiler is large, it is a normal phenomenon. Once the boiler combustion conditions stabilize, the oxygen content display will return to normal. If the unit adjustment is not in place and the deviation is large on both sides, it is necessary to check if the zirconia head is working properly by dismantling the transmitter for inspection. The device requires the operator to adjust the gas flow. The gaseous and reference state gases should continuously flow through the electrode without stopping, and there should be no dead ends. However, too large a flow will have a cooling effect, making the cell temperature uneven and causing errors. If the flow is too small, it is not only easy to form stagnant gas flow and dead zones but also may cause local changes in oxygen concentration due to the conduction of oxygen ions, thus affecting the accuracy of the measurement and causing deviations on both sides.

    6. On-site interference causes failures.

    For newly installed instruments, due to the strong electromagnetic field, when an unstable fault occurs, the first thing to consider is the interference issue.


產品中心 Products
在線客服 聯系方式 二維碼

服務熱線

0550-2409223

掃一掃,關注我們

皖公網安備 34118102000850號

精品黑人一区二区三区| 国产亚洲精品久久777777| 精品久久久久久中文字幕无码软件| 少妇疯狂迎合欲仙欲死| 无人视频在线观看完整版高清| 亚洲女人被黑人巨大进入| 最后一夜bd高清韩国| 挺进大幂幂的滋润花苞御女天下| 日韩精品极品视频在线观看免费 | 亚洲av无码国产精品夜色午夜| 国产亚洲午夜高清国产拍精品| 欧美《熟妇的荡欲》在线观看 | 欧美日韩一区二区三区自拍| 美女脱了内裤张开腿让男人桶网站| 欧亚乱熟女一区二区在线| 免费人成在线观看视频播放| 国产乱人伦偷精品视频免下载| 成熟yin荡美妞a片视频麻豆| 亚洲国产成人久久精品大牛影视| 国产精品毛片无遮挡高清| 国精品无码人妻一区二区三区| 新版天堂资源在线资源| 粗大的内捧猛烈进出在线视频| 欧美黑人乱大交bd| 亚洲成av人片在www色猫咪| 再用点力今晚随你弄| 亚洲综合AV一区二区三区| 50歳のバツ1熟女とハメ撮り| 人人妻人人澡人人爽欧美一区九九| 两腿间花蒂被吸得肿了视频| 精品无码久久久久久久久| 强睡邻居人妻中文字幕| 亚洲A∨国产AV综合AV| 男男乱J伦高HH黄暴双性| 娇妻在卧室里被领导爽 | 人妻熟妇女的欲乱系列| 亚洲精品久久无码午夜一区二区| 亚洲精品乱码久久久久久按摩| 再深点灬舒服灬太大了霍水| 国产肥熟女视频一区二区三区 | 老司机午夜精品99久久免费|